Tools Needed For Vinyl Plank Flooring Installation

Tools Needed For Vinyl Plank Flooring Installation – Practical instructions for preparing the base, taking the necessary measurements, cutting the boards correctly and finally installing the vinyl plank flooring.

We recommend this guide to any homeowner interested in DIY vinyl plank flooring.

Tools Needed For Vinyl Plank Flooring Installation

Tools Needed For Vinyl Plank Flooring Installation

Preparation is important because it simplifies the installation process and allows for better results and a properly installed floor.

Project Source Flooring 4 Pc Installation Kit In The Hard Surface Flooring Tools Department At Lowes.com

Optionally, you may need self-leveling (pre-mixed or powdered, as desired), plywood, silicone mastic, box and scissors, and a hand-held pole saw.

Vinyl sheets must be acclimated to the temperature, humidity and general condition of the new room before installation. So, unwrap the boards and leave them in the room for at least 48 hours. Please note that the room temperature must be kept at least 18 C.

You will need to remove basements and existing floors. Some manufacturers claim that vinyl planks can be installed over existing vinyl siding as long as it is only one layer thick. However, we still recommend removing the vinyl to ensure proper adhesion between the new floor and the subfloor.

Be sure to prepare the base well. It should be dry, clean, flat and as smooth as possible. Concrete floors may need to be sanded to get out some high spots or self-leveled to fill in gaps. Please note that you must wait until the self-levelling is completely dry before installing the floor. If you have a wood floor, you may need to cover it with plywood to make it exactly smooth.

Installing Vinyl Plank Flooring On Concrete: Complete Guide

Some types of vinyl flooring require undercoating; others are thick enough without it. In any case, you should check with the flooring manufacturer to see if vinyl planks require an underlay.

If you decide to put a board on a concrete floor, check its moisture content. It should not exceed 70-75%, otherwise a moisture-resistant membrane must be used. You can find more detailed information on the preparation of concrete and laminate floors on our website.

In most cases, the walls of the room are curved to some extent. Therefore, it is very important to design the floor in such a way that the boards can be laid properly, but not tightly. To do this, measure the length of the walls and find the center of each wall. Mark with white chalk. After that, chalk the lines between the middle of the two opposite walls. The result will be a drawing of a white chalk cross on the floor.

Tools Needed For Vinyl Plank Flooring Installation

Then measure the distance between one of the lines and the far edge of the wall parallel to it. Mark this place with chalk. Measure the same distance between the two ends of the line and the wall and place two more marks. Finally, connect all three marks in a line with chalk.

Wood & Laminate Tools

Now it’s time to calculate the width of the boards placed in the last rows. Take the distance between the center of your room (the chalk line crossing the room) and one of the walls (the chalk line next to the wall) and calculate how many whole boards fit in that distance. Note that you may need to cut some boards lengthwise or crosswise to fill the gap between the last full row of boards and the wall. Do this before installation. Double-check all measurements and cut a board or two first to make sure they fit properly.

If you are planning to install vinyl flooring in your bathroom, be prepared for additional work as you will need to bend the boards to fit around the sink, tub, shower or toilet base. In such cases, we recommend making a special cardboard or thick paper template. Remember that vinyl planks are easier to cut, so consider this type of flooring.

Cut the board with a sharp knife, give yourself a metal ruler. If a knife is not enough at hand, try using a hand hacksaw. If you’re not sure how to properly cut vinyl plank flooring, buy a plank and cut it into several pieces to practice.

The installation steps depend on the type of boards (peel and stick), so we decided to describe this process separately for each type.

How To Install Vinyl Plank Flooring

Start laying down the vinyl from one wall (at the chalk line). Take a board and use a special knife to cut a special tongue from its long side. You need to attach this side without the tongue to the wall. Place the first board on the floor, take the second one and place it with the shorter side at a slight angle in front of the shorter side of the first piece. Carefully fold the second one in and fold it down until you hear a slight click. Repeat this process until the first line appears.

To start the second row, take a board and insert its tongue into the groove of the first board of the first row. Turn the second part until you hear a click. On the other board, you need to fasten the short sides first, then connect its tongue to the groove of the first row of boards. This way you can install all the boards and cover all the floors.

Peel and stick signs are relatively easy to install. You don’t need to buy additional glue, because all boards are already coated with glue at the place of manufacture. Take out the first board and peel off the protective coating from the bottom. Glue the board exactly to the floor, aligning it with the chalk line. Repeat the procedure. Place the boards close together and make sure there are no gaps between them.

Tools Needed For Vinyl Plank Flooring Installation

If you want to install vinyl planks in the bathroom, you need to fill all the small openings around the toilet base or the tub with a special silicone putty.

How To Measure For Flooring In 4 Steps

After you have assembled the basements, make sure there are no gaps or holes between them and the last vinyl plank.

Laminate types – basic classifications How to install a floating laminate floor How to repair a parquet floor yourself How to sand a hardwood floor

We use cookies in order to provide the best experience on our website. If you continue to use this page, we assume you are happy with it.OkPrivacy Policy We renovated our basement in the last few weeks and this post shows how we installed vinyl plank flooring.

Click HERE for our blog post on How to Remove Carpet Like a Pro and click HERE for a YouTube video.

Tapping Block For Vinyl Plank Laminate And Wood Flooring Installation Wood Floor Installation Tools

Our basement has two bedrooms, two bathrooms, a long hallway, a half bath and a living room. The living room and half bath are part of the original house (old concrete floor with lots of paint stains), and the two bedrooms, two bathrooms and the hall are what we added in 2013.

Because of the square meters and the disassembly of the toilets and toilets, it was a lot of work for us middle-aged people, but it was worth it! It took us 6 full days.

If the floor is plywood, some of the wood may need to be replaced. When I installed vinyl siding on my mom’s house, we had to add a layer of plywood.

Tools Needed For Vinyl Plank Flooring Installation

This time the floor was built over concrete and the riser of the floor had to be sanded where the old and new floor met.

Vinyl Plank Flooring In An Rv

Because we did it room by room. We moved furniture to another room and in some cases we left some large items (desk, headboard, couch, etc.) on one side of the room and moved them to the other side of the room after laying the floor. Click here to see how we made this headboard from an old door.

Place the scrap flooring under the oscillating multi tool (I love this tool) to cut the bottom of each door jam.

Place a piece of flooring under each door to determine if you need to cut the bottom of the door so it doesn’t rub against the floor.

We held it level with clamps (the level is just to keep it straight) and then cut the bottom of the door with our DeWalt circular saw.

Beginner’s Guide To Installing Vinyl Plank Flooring • Craving Some Creativity

We didn’t want any threshold; instead, we wanted a continuous floor from room to room. So we had to be very strategic about where we started in the basement.

Since we had a continuous floor from room to room, we had to work “backwards” in several areas. Working backwards is harder, so you want to do as little as possible.

You want the boards to be offset (not all the seams line up). We started with full board in the front row. After completing this row, we cut the first board in the next row so that the seams are offset.

Tools Needed For Vinyl Plank Flooring Installation

I unpacked about 10 boxes of flooring at a time. I opened each box with a putty knife. . . so many boxes!

Inch 310mm Heavy Duty Pull Bar For Vinyl Plank Flooring And Laminate Wood Flooring Installation Tool: Amazon.com: Tools & Home Improvement

There are four different patterns, each printed in opposite directions, for a total of 8 patterns. Sorting helped me

Vinyl flooring tools needed, vinyl plank installation tools, vinyl plank flooring installation, tools needed for luxury vinyl plank flooring, tools needed for vinyl plank flooring, tools needed to install luxury vinyl plank flooring, vinyl plank flooring tools needed, vinyl plank flooring installation tools, tools for vinyl plank flooring, plank flooring installation tools, vinyl plank flooring tools, tools needed for installing vinyl plank flooring

Leave a Reply

Your email address will not be published. Required fields are marked *